UDP-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, Counter64,
Unsigned32, IpAddress, mib-2 FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF
InetAddress, InetAddressType,
InetPortNumber FROM INET-ADDRESS-MIB;
udpMIB MODULE-IDENTITY
LAST-UPDATED "200505200000Z" -- May 20, 2005
ORGANIZATION
"IETF IPv6 Working Group
http://www.ietf.org/html.charters/ipv6-charter.html"
CONTACT-INFO
"Bill Fenner (editor)
AT&T Labs -- Research
75 Willow Rd.
Menlo Park, CA 94025
Phone: +1 650 330-7893
Email: <fenner@research.att.com>
John Flick (editor)
Hewlett-Packard Company
8000 Foothills Blvd. M/S 5557
Roseville, CA 95747
Phone: +1 916 785 4018
Email: <john.flick@hp.com>
Send comments to <ipv6@ietf.org>"
DESCRIPTION
"The MIB module for managing UDP implementations.
Copyright (C) The Internet Society (2005). This
version of this MIB module is part of RFC 4113;
see the RFC itself for full legal notices."
REVISION "200505200000Z" -- May 20, 2005
DESCRIPTION
"IP version neutral revision, incorporating the
following revisions:
- Added udpHCInDatagrams and udpHCOutDatagrams in order
to provide high-capacity counters for fast networks.
- Added text to the descriptions of all counter objects
to indicate how discontinuities are detected.
- Deprecated the IPv4-specific udpTable and replaced it
with the version neutral udpEndpointTable. This
table includes support for connected UDP endpoints
and support for identification of the operating
system process associated with a UDP endpoint.
- Deprecated the udpGroup and replaced it with object
groups representing the current set of objects.
- Deprecated udpMIBCompliance and replaced it with
udpMIBCompliance2, which includes the compliance
information for the new object groups.
This version published as RFC 4113."
REVISION "199411010000Z" -- November 1, 1994
DESCRIPTION
"Initial SMIv2 version, published as RFC 2013."
REVISION "199103310000Z" -- March 31, 1991
DESCRIPTION
"The initial revision of this MIB module was part of
MIB-II, published as RFC 1213."
::= { mib-2 50 }
-- the UDP group
udp OBJECT IDENTIFIER ::= { mib-2 7 }
udpInDatagrams OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of UDP datagrams delivered to UDP
users.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by discontinuities in the
value of sysUpTime."
::= { udp 1 }
udpNoPorts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of received UDP datagrams for which
there was no application at the destination port.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by discontinuities in the
value of sysUpTime."
::= { udp 2 }
udpInErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of received UDP datagrams that could not be
delivered for reasons other than the lack of an
application at the destination port.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by discontinuities in the
value of sysUpTime."
::= { udp 3 }
udpOutDatagrams OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of UDP datagrams sent from this
entity.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by discontinuities in the
value of sysUpTime."
::= { udp 4 }
udpHCInDatagrams OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of UDP datagrams delivered to UDP
users, for devices that can receive more than 1
million UDP datagrams per second.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by discontinuities in the
value of sysUpTime."
::= { udp 8 }
udpHCOutDatagrams OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of UDP datagrams sent from this
entity, for devices that can transmit more than 1
million UDP datagrams per second.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by discontinuities in the
value of sysUpTime."
::= { udp 9 }
--
-- { udp 6 } was defined as the ipv6UdpTable in RFC2454's
-- IPV6-UDP-MIB. This RFC obsoletes RFC 2454, so { udp 6 } is
-- obsoleted.
--
-- The UDP "Endpoint" table.
udpEndpointTable OBJECT-TYPE
SYNTAX SEQUENCE OF UdpEndpointEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing information about this entity's UDP
endpoints on which a local application is currently
accepting or sending datagrams.
The address type in this table represents the address
type used for the communication, irrespective of the
higher-layer abstraction. For example, an application
using IPv6 'sockets' to communicate via IPv4 between
::ffff:10.0.0.1 and ::ffff:10.0.0.2 would use
InetAddressType ipv4(1).
Unlike the udpTable in RFC 2013, this table also allows
the representation of an application that completely
specifies both local and remote addresses and ports. A
listening application is represented in three possible
ways:
1) An application that is willing to accept both IPv4
and IPv6 datagrams is represented by a
udpEndpointLocalAddressType of unknown(0) and a
udpEndpointLocalAddress of ''h (a zero-length
octet-string).
2) An application that is willing to accept only IPv4
or only IPv6 datagrams is represented by a
udpEndpointLocalAddressType of the appropriate
address type and a udpEndpointLocalAddress of
'0.0.0.0' or '::' respectively.
3) An application that is listening for datagrams only
for a specific IP address but from any remote
system is represented by a
udpEndpointLocalAddressType of the appropriate
address type, with udpEndpointLocalAddress
specifying the local address.
In all cases where the remote is a wildcard, the
udpEndpointRemoteAddressType is unknown(0), the
udpEndpointRemoteAddress is ''h (a zero-length
octet-string), and the udpEndpointRemotePort is 0.
If the operating system is demultiplexing UDP packets
by remote address and port, or if the application has
'connected' the socket specifying a default remote
address and port, the udpEndpointRemote* values should
be used to reflect this."
::= { udp 7 }
udpEndpointEntry OBJECT-TYPE
SYNTAX UdpEndpointEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a particular current UDP endpoint.
Implementers need to be aware that if the total number
of elements (octets or sub-identifiers) in
udpEndpointLocalAddress and udpEndpointRemoteAddress
exceeds 111, then OIDs of column instances in this table
will have more than 128 sub-identifiers and cannot be
accessed using SNMPv1, SNMPv2c, or SNMPv3."
INDEX { udpEndpointLocalAddressType,
udpEndpointLocalAddress,
udpEndpointLocalPort,
udpEndpointRemoteAddressType,
udpEndpointRemoteAddress,
udpEndpointRemotePort,
udpEndpointInstance }
::= { udpEndpointTable 1 }
UdpEndpointEntry ::= SEQUENCE {
udpEndpointLocalAddressType InetAddressType,
udpEndpointLocalAddress InetAddress,
udpEndpointLocalPort InetPortNumber,
udpEndpointRemoteAddressType InetAddressType,
udpEndpointRemoteAddress InetAddress,
udpEndpointRemotePort InetPortNumber,
udpEndpointInstance Unsigned32,
udpEndpointProcess Unsigned32
}
udpEndpointLocalAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address type of udpEndpointLocalAddress. Only
IPv4, IPv4z, IPv6, and IPv6z addresses are expected, or
unknown(0) if datagrams for all local IP addresses are
accepted."
::= { udpEndpointEntry 1 }
udpEndpointLocalAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The local IP address for this UDP endpoint.
The value of this object can be represented in three
possible ways, depending on the characteristics of the
listening application:
1. For an application that is willing to accept both
IPv4 and IPv6 datagrams, the value of this object
must be ''h (a zero-length octet-string), with
the value of the corresponding instance of the
udpEndpointLocalAddressType object being unknown(0).
2. For an application that is willing to accept only IPv4
or only IPv6 datagrams, the value of this object
must be '0.0.0.0' or '::', respectively, while the
corresponding instance of the
udpEndpointLocalAddressType object represents the
appropriate address type.
3. For an application that is listening for data
destined only to a specific IP address, the value
of this object is the specific IP address for which
this node is receiving packets, with the
corresponding instance of the
udpEndpointLocalAddressType object representing the
appropriate address type.
As this object is used in the index for the
udpEndpointTable, implementors of this table should be
careful not to create entries that would result in OIDs
with more than 128 subidentifiers; else the information
cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3."
::= { udpEndpointEntry 2 }
udpEndpointLocalPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The local port number for this UDP endpoint."
::= { udpEndpointEntry 3 }
udpEndpointRemoteAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address type of udpEndpointRemoteAddress. Only
IPv4, IPv4z, IPv6, and IPv6z addresses are expected, or
unknown(0) if datagrams for all remote IP addresses are
accepted. Also, note that some combinations of
udpEndpointLocalAdressType and
udpEndpointRemoteAddressType are not supported. In
particular, if the value of this object is not
unknown(0), it is expected to always refer to the
same IP version as udpEndpointLocalAddressType."
::= { udpEndpointEntry 4 }
udpEndpointRemoteAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The remote IP address for this UDP endpoint. If
datagrams from any remote system are to be accepted,
this value is ''h (a zero-length octet-string).
Otherwise, it has the type described by
udpEndpointRemoteAddressType and is the address of the
remote system from which datagrams are to be accepted
(or to which all datagrams will be sent).
As this object is used in the index for the
udpEndpointTable, implementors of this table should be
careful not to create entries that would result in OIDs
with more than 128 subidentifiers; else the information
cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3."
::= { udpEndpointEntry 5 }
udpEndpointRemotePort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The remote port number for this UDP endpoint. If
datagrams from any remote system are to be accepted,
this value is zero."
::= { udpEndpointEntry 6 }
udpEndpointInstance OBJECT-TYPE
SYNTAX Unsigned32 (1..'ffffffff'h)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The instance of this tuple. This object is used to
distinguish among multiple processes 'connected' to
the same UDP endpoint. For example, on a system
implementing the BSD sockets interface, this would be
used to support the SO_REUSEADDR and SO_REUSEPORT
socket options."
::= { udpEndpointEntry 7 }
udpEndpointProcess OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The system's process ID for the process associated with
this endpoint, or zero if there is no such process.
This value is expected to be the same as
HOST-RESOURCES-MIB::hrSWRunIndex or SYSAPPL-MIB::
sysApplElmtRunIndex for some row in the appropriate
tables."
::= { udpEndpointEntry 8 }
-- The deprecated UDP Listener table
-- The deprecated UDP listener table only contains information
-- about this entity's IPv4 UDP end-points on which a local
-- application is currently accepting datagrams. It does not
-- provide more detailed connection information, or information
-- about IPv6 endpoints.
udpTable OBJECT-TYPE
SYNTAX SEQUENCE OF UdpEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"A table containing IPv4-specific UDP listener
information. It contains information about all local
IPv4 UDP end-points on which an application is
currently accepting datagrams. This table has been
deprecated in favor of the version neutral
udpEndpointTable."
::= { udp 5 }
udpEntry OBJECT-TYPE
SYNTAX UdpEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"Information about a particular current UDP listener."
INDEX { udpLocalAddress, udpLocalPort }
::= { udpTable 1 }
UdpEntry ::= SEQUENCE {
udpLocalAddress IpAddress,
udpLocalPort Integer32
}
udpLocalAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The local IP address for this UDP listener. In the
case of a UDP listener that is willing to accept
datagrams for any IP interface associated with the
node, the value 0.0.0.0 is used."
::= { udpEntry 1 }
udpLocalPort OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The local port number for this UDP listener."
::= { udpEntry 2 }
-- conformance information
udpMIBConformance OBJECT IDENTIFIER ::= { udpMIB 2 }
udpMIBCompliances OBJECT IDENTIFIER ::= { udpMIBConformance 1 }
udpMIBGroups OBJECT IDENTIFIER ::= { udpMIBConformance 2 }
-- compliance statements
udpMIBCompliance2 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for systems that implement
UDP.
There are a number of INDEX objects that cannot be
represented in the form of OBJECT clauses in SMIv2, but
for which we have the following compliance
requirements, expressed in OBJECT clause form in this
description clause:
-- OBJECT udpEndpointLocalAddressType
-- SYNTAX InetAddressType { unknown(0), ipv4(1),
-- ipv6(2), ipv4z(3),
-- ipv6z(4) }
-- DESCRIPTION
-- Support for dns(5) is not required.
-- OBJECT udpEndpointLocalAddress
-- SYNTAX InetAddress (SIZE(0|4|8|16|20))
-- DESCRIPTION
-- Support is only required for zero-length
-- octet-strings, and for scoped and unscoped
-- IPv4 and IPv6 addresses.
-- OBJECT udpEndpointRemoteAddressType
-- SYNTAX InetAddressType { unknown(0), ipv4(1),
-- ipv6(2), ipv4z(3),
-- ipv6z(4) }
-- DESCRIPTION
-- Support for dns(5) is not required.
-- OBJECT udpEndpointRemoteAddress
-- SYNTAX InetAddress (SIZE(0|4|8|16|20))
-- DESCRIPTION
-- Support is only required for zero-length
-- octet-strings, and for scoped and unscoped
-- IPv4 and IPv6 addresses.
"
MODULE -- this module
MANDATORY-GROUPS { udpBaseGroup, udpEndpointGroup }
GROUP udpHCGroup
DESCRIPTION
"This group is mandatory for systems that
are capable of receiving or transmitting more than
1 million UDP datagrams per second. 1 million
datagrams per second will cause a Counter32 to
wrap in just over an hour."
::= { udpMIBCompliances 2 }
udpMIBCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for IPv4-only systems that
implement UDP. For IP version independence, this
compliance statement is deprecated in favor of
udpMIBCompliance2. However, agents are still
encouraged to implement these objects in order to
interoperate with the deployed base of managers."
MODULE -- this module
MANDATORY-GROUPS { udpGroup }
::= { udpMIBCompliances 1 }
-- units of conformance
udpGroup OBJECT-GROUP
OBJECTS { udpInDatagrams, udpNoPorts,
udpInErrors, udpOutDatagrams,
udpLocalAddress, udpLocalPort }
STATUS deprecated
DESCRIPTION
"The deprecated group of objects providing for
management of UDP over IPv4."
::= { udpMIBGroups 1 }
udpBaseGroup OBJECT-GROUP
OBJECTS { udpInDatagrams, udpNoPorts, udpInErrors,
udpOutDatagrams }
STATUS current
DESCRIPTION
"The group of objects providing for counters of UDP
statistics."
::= { udpMIBGroups 2 }
udpHCGroup OBJECT-GROUP
OBJECTS { udpHCInDatagrams, udpHCOutDatagrams }
STATUS current
DESCRIPTION
"The group of objects providing for counters of high
speed UDP implementations."
::= { udpMIBGroups 3 }
udpEndpointGroup OBJECT-GROUP
OBJECTS { udpEndpointProcess }
STATUS current
DESCRIPTION
"The group of objects providing for the IP version
independent management of UDP 'endpoints'."
::= { udpMIBGroups 4 }
END
Mr. DellatioNx196 GaLers xh3LL Backd00r 1.0, Coded By Mr. DellatioNx196 - Bogor BlackHat